AutoDoor Experts

LCN 8310-804-1 – Door Mount Safety Sensor

$110.00

Model 8310-804-1. Installer-grade door mount safety sensor.

SKU: 8310-804-1

Category: Sensors

Tags: automatic doors, installer-grade, LCN

Brands: LCN

Description

Contains one active sensor
module to detect obstruction(s)
on leading edge of door

Additional information

Brand	LCN

Reviews

There are no reviews yet.

Be the first to review “LCN 8310-804-1 – Door Mount Safety Sensor”

LCN 8310 Series is a modular system of touchless and push-plate door actuators, wireless transmitter/receiver sets, mounting boxes, escutcheons, weather/trim rings, safety sensors, and accessory kits used to remotely actuate LCN automatic swing-door operators (e.g., 4630/4640, 7900 pneumatic auto-equalizer, 9100 Benchmark, Senior Swing 2800/9500, Mid Swing 2900/9700 series). Touchless actuators and hardwired push plates require a wired, low-voltage power/control connection back to the door operator control box; most are also compatible with a 433 MHz or 900 MHz wireless transmitter/receiver pair for wireless actuation signaling instead of a run of activation wire. A subset of push plates (8310-852WP/853WP) are fully wireless/battery powered with no field control wiring at the plate itself (only the receiver, sold separately, is wired to the operator).

Product specifications
Touchless actuator supply (8310-813)	12-24 VAC ±10% or 12-24 VDC +30%/-10%, SELV-compatible power supplies only; power consumption < 1.5W; output is a voltage-free relay (max 60VDC/125VAC, 1A resistive, 30W)
900 MHz receiver input voltage (8310-880)	12-24 VAC/VDC; relay contact rating 1.0A@30VDC, 0.3A@60VDC, 0.5A@125VAC
Wireless transmitter power consumption (900 MHz)	30mA (standard TX) / 40mA (RX) / 22mA (retrofit TX)
Receiver capacity	up to 74-75 transmitters per standard receiver; unlimited for 'universal' mode
Low-voltage wiring	Required
Basis	Structured, independently qualified product connection evidence
Preparation	Prepare the sensor housing and mounting holes on the door, maintaining clearance from the jamb and adjacent hardware. Position it as instructed for the actual handing; mount the housing with the provided screws. Provide a wire-passage hole only when the selected route needs one, and use the manufacturer routing drawing before drilling.
Electrical	Low-voltage wiring is required. Supply the8310-804 sensor with12-24VAC/VDC (+/-10%) at power terminals7/8 from a Class2 source limited to15W. Choose the relay contact and monitoring/inhibit connections for the actual door control: relay common6, normally open4 or normally closed5; monitoring test1/2 and inhibit3/2 are separate functions. These terminal functions are not an installation-wide conductor count. Field conductor total, physical cable runs, gauge and shielding require the selected control diagram and route. The internal master/slave ribbon cable is not a field cable run.
Preparation required	Yes
Electrical wiring required	Yes
Conditional connections	Door mount harness for the 8310-804-1 when used with Senior Swing: cable runs quantity unspecified; conductor count unspecified; wire type not documented; size unspecified; shielding unspecified; rating unspecified; endpoints 8310-804-1 door mount safety sensor to Senior Swing operator; when Installation configuration is Optional accessory selected: IF the sensor is used with Senior Swing, the 8310-847 Door Mount Harness is required and ordered separately. The catalogue does not document the harness as a field cable or give its conductor count.; Remote 24V power for the sensor: cable runs quantity unspecified; conductor count unspecified; wire type not documented; size unspecified; shielding unspecified; rating unspecified; endpoints 24V transformer (8310-824 or 8310-824P) to 24V sensor/receiver; when Installation configuration is Optional accessory selected: IF remote 24V power is chosen, the optional 8310-824 hardwired or 8310-824P plug-in transformer can power any 24V sensor/receiver. The catalogue does not state that the 8310-804-1 itself needs 24V.