4-1/2\” Square push plate (concealed screws) with sounder, illuminated RED/GREEN/BLUE surface mount CM-54i box
Series: CM-54, CM-55 & CM-57 Series
Type: Illuminated Push Plate Enclosures & Kits
Configuration: AURA(tm) Illuminated Switch Kits – Surface Mount
4-1/2" Square push plate (concealed screws) with sounder, illuminated RED/GREEN/BLUE surface mount CM-54i box
Brand: Camden
Manufacturer Part Number: CM-45/X54
Source: Camden Controls product page
| graphic | /1 blank, /2 wheelchair blue, /2AL wheelchair+arrow left, /2AR wheelchair+arrow right, /3 push to open black, /3F poussez pour ouvrir blac, /4 wheelchair+push to open, /4AL wheelchair+arrow left bl, /4AR wheelchair+arrow right b, /4F wheelchair+french black, /8 push to lock black, /8B lock symbol+push to lock, /8D push to lock door black, /8F poussez pour verrouiller |
|---|
Camden's Aura Illuminated push plate switch series provides high-visibility, ADA-compliant door activation switches available in red, green, or blue illumination, with an audible sounder and Form 'C' contacts. The line is offered in surface-mount square (CM-54i), flush-mount square (CM-55i), and flush-mount round (CM-57GR) configurations.
| Voltage | 12V or 24V AC/DC |
|---|---|
| Current draw | 130mA |
| Contact type | 1 Form 'C' |
| Contact rating | 3 Amps @ 24V AC/DC |
| Dimensions | CM-54i: 5 1/4" W x 5 1/4" H x 2" D (133mm x 133mm x 51mm); CM-55i: 6 1/2" W x 6 1/2" H x 2" D (165mm x 165mm x 51mm); CM-57GRB: 6 5/8" DIA. x 2" D (168mm x 51mm) |
| Low-voltage wiring | Required |
| Basis | Structured, independently qualified product connection evidence |
| Preparation | For the CM-54i surface box, choose the wire entry or centre knockout. Drill the four mounting holes (11/64 inch minimum, provided indents on 3 inch centres), pull wiring through and fasten the box to the wall with four screws. Install optional signage first. Route wiring through the circuit-board centre opening, secure the board with its two supplied screws, then route the local push-switch wires through the diffuser. Fit any selected TX-9 before fitting the board and diffuser. Attach the push plate with its supplied Allen screws and hand-tighten; connect power and test. Confirm the delivered box/template before cutting because published dimensions differ. |
| Electrical | Supply 12 or 24 V AC/DC to the two power terminals; the diagram states they are not polarity sensitive. The enclosure manual states 250 mA at 12 VDC or 110 mA at 24 VDC, while the shared specification states 130 mA. Confirm the delivered revision and supply sizing with Camden. The illustrated direct low-voltage door input uses relay COM and NO; NC is unused in that example. Optional remote LED colour change uses a remote dry-contact pair; select LOCAL and omit that pair when colour follows the push switch. The push-switch connection within the box and optional TX-9 leads are local connections, not additional external cable runs. The 3 V DC output is for TX-9 only. Manual relay rating is 3 A at 30 VDC, while the shared specification says 3 A at 24 V AC/DC; confirm the applicable contact rating before choosing a load. Set speaker, relay and colour operation from the actual labelled board; choose cable type, gauge, routing and physical run quantities for the installation. |
| Preparation required | Yes |
| Electrical wiring required | Yes |
| Conditional connections | CM-45/X54 12/24 V AC/DC supply: cable runs quantity unspecified; 2 conductor(s); wire type not documented; size unspecified; shielding unspecified; rating Cable type/gauge/shielding, routing and physical run quantity are installation-specific.; endpoints External low-voltage supply to Enclosure power terminals; when Installation configuration is Base enclosure power input; terminals not polarity sensitive.; CM-45/X54 normally-open low-voltage door input: cable runs quantity unspecified; 2 conductor(s); wire type not documented; size unspecified; shielding unspecified; rating Cable type/gauge/shielding, routing and physical run quantity are installation-specific.; endpoints Relay COM and NO to Selected external low-voltage door input; when Installation configuration is Illustrated NO/COM direct wired configuration only; NC unused.; CM-45/X54 optional remote LED colour contact: cable runs quantity unspecified; 2 conductor(s); wire type not documented; size unspecified; shielding unspecified; rating Cable type/gauge/shielding, routing and physical run quantity are installation-specific.; endpoints Enclosure remote colour terminals to External dry-contact switch or relay; when Installation configuration is Only if remote LED colour operation is selected; omitted for LOCAL operation. |
Reviews
There are no reviews yet.